Futaba 05102713 R7208SB(ERP) Remote Control Receiver, 2.4 Ghz, FASSTest (FTR5102713)

Futaba 05102713 R7208SB (ERP) FassStest Control Receiver

Brand:Futaba
Stock Code:FTR5102713
Type:Buyer

Box content

• 1 R7208SB (ERP) Control Receiver

Features

• Transmission Type: FassStest
• Frequency range: 2.4 GHz
• Channels: 8 pwm / 18 s.bus
• Transmission Power: 100 MW EIRP
• S.BUS Port: S.BUS / S.BUS2
• Voltage range: 3.7 - 8,4 V
• Weight: 11 Gr
• Dimensions: 24.9 x 38.8 x 14.3 mm
• 8/18 Channel Fassestest Receiver
• Double RX connection
• Telemetry with S.BUS2
• 32 channel telemetry
• PWM channels can be selected 1-8 or 9-16
• S.BUS / S.BUS2 POINT POINT
• High voltage (HV)
• Antenna variety
• Digital Servo with impact switching

You can find the ingredients you need to finish this product at the bottom of the page

With Futaba R7208SB, Futaba offers a particularly light and small buyer with a telemetry and new dual rx function. The narrow design makes it ideal for use in narrow trunks.
When R7208SB is operated in dual RX mode, a second S.BUS/S.BUS2 receiver is connected to the recipient on the R7208SB and operated in parallel. BUILDING BACKGRISH INCREASES MODEL RECEIVES: In case of a problem with the main buyer, the system instantly switches to the second recipient.
To run the R7208SB in binary connection mode, an additional S.BUS/S.BUS2 receiver is required.
R7208SB has an antenna variety. The recipient constantly compares which antenna has a better signal and switch to it instantly.
Analog or digital servos can be connected to the ports from 1 to 8. To make shorter response times possible, the Servo output signal for digital servos can be changed to 6.3 ms (instead of 16 ms for analog servos). PWM ports can be replaced as an alternative to the connection points from 9 to 18 can be used. Or the ports can be used as additional s.Bus2 ports.
Other S.BUS components such as S.BUS servo or gyroscopes, flight bar -free systems or regulators can be connected to the S.BUS port. All S.BUS servos are digitally addressed and can be connected to a single servo line (3 cables). Although 4 servo is installed in a Canada, Canada only goes to one servo cable. This makes all the wiring very simple and clear. If analog servos are to be used in S.BUS, they must be connected using a PWM adapter.
S.BUS2 sensors can be connected to S.BUS2 ports. They transmit telemetry data set up to 32. The recipient has an integrated telemetry transmitter that transmits the data to the donor (Fassestest only). This allows the measured values ​​to be displayed or acoustic in the transmitter. In addition, the buyer always transmits the voltage of the recipient power supply (the voltage sensor is integrated) and always transmits the signal power at any time.
The receiver supports HV (high voltage) and can be operated directly with a 2S lipo battery. Always be sure that connected servos are also designed for HV!
 

About Futaba

Futaba Corporation was founded in 1948 as a manufacturer and seller of receiving vacuum tubes in Japan. Futaba, which uses vacuum tube technology, has started to produce vacuum fluorescent screens. In 1962, Futaba began to produce a press mold set components as well as radio control equipment and founded two of the primary sections of the company. This was followed by the development of mold basic components and the addition of VFD modules to complete the futaba's main product range. Our company's US -based branch Futaba Corporation of America (FCA) supports the same technologies and is the leading provider of electronic production services. (EMS) includes PCB devices to complete box construction, test and engineering design.

☛ Click for detailed photos of the product ☚

Model Construction Guide